Overview of fitting locations - injection system engines 2,0 EA888 gen III BZ

4-cyl. direct injection engine (2.0L 4V EA888 gen III BZ, turbocharger, chain drive)
Engine code: CZPA, CZPB, CZPC, DKZA, DKZC.

VW Tiguan (AD1) 2016 - , VW Tiguan RUS (BT1) 2017 - ,
VW T-Roc (A11) 2018 - ,
VW Arteon (3H7) 2018 - ,
VW Polo 6 GTI (AW1) 2018 - .

Overview of fitting locations - engine, top

Overview of fitting locations - engine 2,0 EA888 gen_III_BZ, top

1 - Hall sender 3 - G300-
2 - Fuel pressure regulating valve - N276-
3 - Inlet cam actuator B for cylinder 3 - N593-
4 - Inlet cam actuator B for cylinder 4 - N601-
5 - Inlet cam actuator A for cylinder 4 - N600-
6 - Inlet cam actuator A for cylinder 3 - N592-
7 - Injector, cylinder 4 - N33-
8 - Intake manifold flap air flow control valve - N316-
9 - Intake manifold sender - GX9-
Consists of intake air temperature sender - G42- / intake manifold pressure sender - G71-
10 - Injector, cylinder 3 - N32-
11 - Knock sensor 1 - G61-
12 - Injector, cylinder 2 - N31-
13 - Injector, cylinder 1 - N30-
14 - Intake manifold flap potentiometer - G336-
Bend aside retaining tabs to allow for pulling potentiometer out of intake manifold
15 - Inlet cam actuator B for cylinder 2 - N585-
16 - Inlet cam actuator A for cylinder 1 - N576-
17 - Inlet cam actuator B for cylinder 1 - N577-
18 - Inlet cam actuator A for cylinder 2 - N584-
19 - Activated charcoal filter solenoid valve 1 - N80-
20 - Ignition coil 1 with output stage - N70-
21 - Ignition coil 2 with output stage - N127-
22 - Ignition coil 3 with output stage - N291-
23 - Ignition coil 4 with output stage - N292-

Overview of fitting locations – engine, front

Overview of fitting locations - engine 2,0 EA888 gen_III_BZ, front

1 - Injector 2 for cylinder 1 - N532-
2 - Injector 2 for cylinder 2 - N533-
3 - Injector 2 for cylinder 3 - N534-
4 - Injector 2 for cylinder 4 - N535-
5 - Hall sender - G40-
6 - Stage 3 oil pressure switch - F447-
7 - Engine speed sender - G28-
8 - Actuator for engine temperature regulation - N493-
9 - Air conditioner compressor regulating valve - N280-
10 - Throttle valve module - GX3-
and
Throttle valve drive (electric throttle) - G186-
Angle sender for throttle valve drive - G187-
Angle sender 2 for throttle valve drive - G188-
11 - Alternator with voltage regulator - CX1-
12 - Fuel pressure sender - G247-
13 - Fuel pressure sender for low-pressure - G410-

Overview of fitting locations - engine, right side

Overview of fitting locations - engine 2,0 EA888 gen_III_BZ, right side

1 - Exhaust camshaft control valve 1 - N318-
2 - Inlet camshaft control valve 1 - N205-
3 - Oil pressure switch - F1-
4 - Oil pressure switch for reduced oil pressure - F378-
5 - Piston cooling jet control valve - N522-
6 - Valve for oil pressure control - N428-

Overview of fitting locations - engine, left

Overview of fitting locations - engine 2,0 EA888 gen_III_BZ, left side

1 - Turbocharger air recirculation valve - N249-
2 - Charge pressure positioner - V465- with position sender for charge pressure positioner - G581-
3 - Auxiliary pump for heating -V488-
4 - Oil level and oil temperature sender - G266-
5 - Secondary air inlet valve -N112-
Only engines with secondary air system
6 - Radiator outlet coolant -G62-
7 - Sender 1 for secondary air pressure - G609-
Only engines with secondary air system
8 - Coolant shut-off valve -N82-

Overview of fitting locations – engine, rear

Overview of fitting locations - engine 2,0 EA888 gen_III_BZ, rear

1 - Turbocharger air recirculation valve - N249-
2 - Auxiliary pump for heating -V488-
3 - Radiator outlet coolant - G62-
4 - Charge pressure positioner - V465- with position sender for charge pressure positioner - G581-

Accelerator pedal module - GX2-

Accelerator pedal module GX2 - engine 2,0 EA888 gen_III_BZ, rear

2 - Connector for accelerator pedal module

Fitting location brake light switch - F- / brake pedal switch - F63- and vacuum sender - G608-

Fitting location brake light switch F / brake pedal switch F63 and vacuum sender G608

1 - Brake light switch - F- / brake pedal switch - F63-
2 - Vacuum sender - G608-
On brake servo in engine compartment

Clutch position sender - G476- -2-

Clutch position sender G476 - engine 2,0 EA888 gen_III_BZ

On mounting bracket for clutch pedal -arrow

Fuel pump control unit - J538- -1-

Fuel pump control unit J538 - engine 2,0 EA888 gen_III_BZ

Ignition coils with output stages

Ignition coils with output stages - engine 2,0 EA888 gen_III_BZ

1 - Ignition coil 1 with output stage - N70-
2 - Ignition coil 2 with output stage - N127-
3 - Ignition coil 3 with output stage - N291-
4 - Ignition coil 4 with output stage - N292-
5 - Fuel pressure regulating valve - N276-
6 - Activated charcoal filter solenoid valve 1 - N80-

Injectors (combustion chamber)

Injectors (combustion chamber) - engine 2,0 EA888 gen_III_BZ

1 - No. 1 cyl. injector - N30-
2 - No. 2 cyl. injector - N31-
3 - No. 3 cyl. injector - N32-
4 - No. 4 cyl. injector - N33-
5 - Fuel pressure sender - G247-
6 - Knock sensor 1 - G61-

Intake manifold injectors

Intake manifold injectors - engine 2,0 EA888 gen_III_BZ

1 - Injector 2 for cylinder 1 - N532-
2 - Injector 2 for cylinder 2 - N533-
3 - Injector 2 for cylinder 3 - N534-
4 - Injector 2 for cylinder 4 - N535-
5 - Intake manifold sender - GX9-
6 - Fuel pressure sender for low-pressure - G410-

Fuel pressure sender in high-pressure system

Fuel pressure sender in high-pressure system - engine 2,0 EA888 gen_III_BZ

1 - Fuel pressure sender - G247-

Variable intake manifold

Variable intake manifold - engine 2,0 EA888 gen_III_BZ

1 - Vacuum unit for intake manifold flaps
2 - Intake manifold flap air flow control valve - N316-

Intake manifold flap potentiometer - G336-

Intake manifold flap potentiometer G336 - engine 2,0 EA888 gen_III_BZ

Bend aside retaining tabs to allow for pulling potentiometer out of intake manifold.

Electrical connectors

Electrical connectors - engine 2,0 EA888 gen_III_BZ

1 - For injectors (combustion chamber).
2 - For knock sensor 1 - G61- .
3 - Stage 3 oil pressure switch - F447-
4 - For intake manifold flap valve - N316- , fuel pressure sender - G247- , intake manifold flap potentiometer - G336- , coolant temperature sender - G62- and Hall sender - G40- .

High-pressure pump and Hall sender

High-pressure pump and Hall sender - engine 2,0 EA888 gen_III_BZ

1 - Hall sender 3 - G300-
2 - Fuel pressure regulating valve - N276-
3 - Fuel line leading to fuel rail for injectors (intake manifold)
4 - High-pressure line leading to fuel rail for injectors (combustion chamber)
5 - Fuel pressurisation line from fuel tank
Pfeile - Securing bolts

Engine speed sender - G28- -1-

Engine speed sender G28 - engine 2,0 EA888 gen_III_BZ

Lambda probes

>Lambda probes - engine 2,0 EA888 gen_III_BZ

1 - Connector for Lambda probe 1 after catalytic converter - GX7-
2 - Connector for Lambda probe 1 before catalytic converter -GX10-

Lambda probe 1 before catalytic converter - GX10- -1-

Lambda probe 1 before catalytic converter GX10 - engine 2,0 EA888 gen_III_BZ

Lambda probe 1 after catalytic converter - GX7- -1-

Lambda probe 1 after catalytic converter GX7 - engine 2,0 EA888 gen_III_BZ

Как здесь найти нужную информацию?
Расшифровка заводской комплектации автомобиля (англ.)
Расшифровка заводской комплектации VAG на русском!
Диагностика Фольксваген, Ауди, Шкода, Сеат, коды ошибок.

Если вы не нашли информацию по своему автомобилю - посмотрите ее на автомобили построенные на платформе вашего авто.
С большой долей вероятности информация по ремонту и обслуживанию подойдет и для Вашего авто.

  • VWspare

  • Техцентр VWS

  • Kinergo-Russia

  • akpp03.ru

  • Б/У запчасти Volkswagen, Audi

Volkswagen Technical Site ©1999-2019
vwts.ru - aka volkswagen.msk.ru
Контакты, реклама на сайте

Яндекс.Метрика Top.Mail.Ru